These are sturdy double walled units with outer chamber made of M.S. sheet duly enamel painted with inner made up of anodised aluminium or S.S. sheet. The gap between inner and outer chamber is filled with high grade glass wool to avoid thermal losses. Beaded heating elements are placed in ribs, at bottom and sides. Inner chamber is provided with ribs for adjusting perforated shelves to convenient height. Temperature is controlled by "EGO"/"JUMO"GERMAN hydraulic type capillary thermostat from 500C to 2500C ± 10C .

An-L shaped prismatic thermometer is fitted to the unit forreading the chamber temperature. Air ventilators are also provided on the sides of the unit. To work on 220/230volts A.C.

It withstands high temperature up to 350°C . The body of the mantle is spun one piece form non-rusting Aluminium (upto 5.0 Liters Capacity) duly stoving painted. All heating mantles are lagged with special grade mineral wool. To work 220/230 Volts. A.C. Best Regards

With Solid State speed regulator , indication lamp and see through acrylic lid, with head puller but without rotor heads. Mix. Speed 4000 r.p.m. (b) - do- with 0-60 minutes " GERMAN" Timer

This is a double walled unit mounted horizontal on a sturdy, heavy mild steel tubular stand duly painted. Pressure is adjustable from 10 to 20 psi. Fitted with pressure gauge, safety valve and steam release valve. Available with or without boiler. For units fitted with S.S. Boiler, separate valves for injecting the steam into the main chamber and releasing the steam in atmosphere after use are provided. Hydraulically tested upto 40psi, Automatic vacuum breaker is providedTo break the vacuum in case of formation of vacuum due to steam condensation. Inner chamber made of S.S. and outer of Mild Steel duly painted. Fitted with Automatic Pressure Control Switch and Automatic Low Water Level Cut- Off device. Lid is made of S.S. plate with Radial locking system Without steam jacket.

Rectangular Double Walled inside made of Stainless Steel Sheet & outer M.S. sheet duly powder coated. Temperature is controlled by hydraulic thermostat from ambient to 95ºC ± 0.5ºC. The unit consists of 2 pilot lamp & On off switch fitted with ISI immersion heater. Most suitable to work on 220/230 volts A.C. Supply.

Available Sizes:

• 300 x 250 x 100mm (6 holes of 75mm dia)
• 425 x 325 x 100mm (12 holes of 75mm dia)

Useful for stirring centrifugal tubes, test tubes or small flasks. Fitted with a Neoprene rubber cup mounted eccentrically on the shaft against which at its is held the tube with its lower end pressing against the cup. Mixing action is controlled by verying the angle and pressure of the tube against the cup. Fitted with speed control arrangement. To work on 220/230 volts A.C. Supply.

• Construction : Double walled outer M.S. sheet duly powder coated. Inner Aluminium/Stainless Steel with 2/3 Nos. adjustable shelves duly perforated. Having heavy duty M.S. Stand. the door is an impressive structure having glass window & sealed by Rubber Gasket. Gap between the walls is filled with glass wool insulation.
  
• Panel : Consists of Temp. Controller i.e. by thermostat of Digitally controlled by Thermostat/Digital Humidity Controlled by imported humidistate placed inside the chamber. Supplied with Hygrometer to check exact Humidity inside the chamber.
  The Temperature is recorded on the "L" shaped thermometer fitted at the front of the cabinet. The water tank is provided at the bottom and the steam is circulated by water pump/motor fitted at the top of the chamber.
• Humidity Range : Ambient to 95% ± 3%.
• Temperature Range : Ambient to 40ºC/45ºC ± 2ºC.Suitable to work on 220/230 volts A.C. Supply.